10.1.10.1 login IP address is important as it allows you to login to your Comcast Business router in order to set it up and manage it. Whether you want to secure your router, set up a wireless network or a Guest network you need this IP. The Comcast business router login steps described in this article can be applied to a Cisco Business Wireless gateway.
10.1.10.1 is a private IPv4 address and you don’t need a specific permission to use it in your private network. However, there is one thing to worry about:
Only one device in the network can use 10.1.10.1. Otherwise, in case there are two devices using the same IP a so called IP conflict will occur. This can have bad impact on your network or even make it unusable.
The application of 10.1.10.1:
The default router IP is used to allow the user access the router settings just like other default IP addresses, for example 192.168.1.1 or 192.168.0.1. From there the user can manage the router settings and enable, disable or tweak the numerous features the router has to offer, like:
Change the router IP
Change the router password
Change the wireless network name (SSID)
Set up or change the wireless password
Set up Guest network
Set up Parental controls on your home network
However, in order to any of these actions you need to know the 10.1.10.1 login steps.
Guidelines for login at IP address 10.1.10.1
Connect to your network:
You can access the router settings only if you use a device already connected to your network. That’s why you have to connect to your network first either using a wireless connection in case you are using your laptop, tablet or smartphone or a wired connection in case you are using your PC or laptop.
Go to 10.1.10.1 using your browser to open the login page.
You have to use your browser to access the Comcast Business router login page. That’s why you need to type the 10.1.10.1 default login IP in the Address bar or click the 10.1.10.1
Enter the Comcast Business router login details:
In this step you will be required to type the Comcast Business router login username and password. If you haven’t changed these details already, use the default ones. If you have changed them, use the new password instead.
You can find these login details in the user’s manual or on the router. However, the default login details are:
If the default username and password of your wireless gateway are correct you will be redirected to the router settings page.
Now you can go through the menus and make the necessary changes.
However, in case you have changed the Comcast Business router default login details, you will have to reset the router to factory settings.
Frequently Asked Questions about 10.1.10.1 login:
- How to find the default Wifi password?
Take a look at the bottom of your Comcast Business router. The default Wifi password and Network name (SSID) are usually printed on a label.
- I can’t connect to my Wifi network. What now?
Login to your wireless gateway router as described above and disable and then enable the 2.4GHz and 5GHz Wifi network depending on which one you can’t connect.
- How to change the Comcast Business router password?
Once you login to the router using 10.1.10.1 and the default username and password, check the upper right corner of the screen and you will see Change Password. Just type the default password high-speed or can’t touch this and then enter the new password. You will have to type the new password again before you save the changes.
How I can find out my router’s default login and passkey?
There are some different situations! Everyone can forget password or login, so there are some methods to return them. Firstly, check all sides of your device. If there is no sticker with login and passkey, you can check guide book. If nothing helps you, you can check Default Router Passwords page on website.
If your login or passkey were changed, you should reset your router to default settings. It’s not difficult. You have to hold special reset pushbutton for about 20 seconds. After that, your router’s identification information will be returned to factory defaults.
Common issues during the use of 10.1.10.1:
- 1.10.1 isn’t working:
Firstly, you need to ensure that your gateway is not in the bridge mode. If it is then your connection to the 10.1.10.1 IP will be disabled by default.
Just in case you are not using any of the Comcast Static IP on a Comcast gateway(CG) including SMCD#G, Netgear 3000 DCR or DPC3939B, then you need to hit the reset button for a minimum of 15 seconds.
Now once reset, your default parameters including the access to 10.1.10.1 gateway will be back.
- 1.10.1 timed out or refused to connect:
This is again an issue when your router SMCD3G-CCR is into bridge mode– You will often see this problem occurring. The best way to resolve it is by resetting the browser’s settings. A simple power cycle will set things working normally again.
What should I do to set a port?
Usually data is revised by using special hardware and soft, so you don’t need to do make some actions with ports, but there are some situations when you need to define number combination of ports manually:
When you need to connect on private server in game
When you try to configure Torrent application
To specify applications which can be passed through router?
If you need get connection to certain camera
You can get permission if you will use special IP address which used by network, device or program with own port number. For example, we can discuss about security cameras which use IP address to give access for someone who want use it.
Your Camera has its own IP address and port, so when you need to connect to your camera, you need type IP address and port too.
Read More: 10001routernetworkipaddress
Related Search Terms:
- http 10.1-10.1 login
- 10.1.10.1 login comcast
- 10.1.10.1 login page
- 10.1.10.1 router login
- 10.1.10.1 xfinity
There are Wi-Fi routers which provide to configure a few additional Internet connections and specify usage priority. It is more safety than use only two connections.